4225 w. ogden ave, chicago il, 60532
3060 s. calhoun rd, new berlin wisconsin, 53151
LANCE CONSTRUCTION SUPPLIES
.jpg)
H&B
H&B's Flex-Flash® is a polyester scrim reinforced 40-mil thick product formulated with Elvaloy® Kee. It does not drool and combines the best features of other types of flashing, making it a truly superior product. Moisture infiltration can occur at sills, projections, recesses, intersections and mortar joints.
FLEX FLASH
H&B
Mortar Trap™ is a mortar collection device manufactured from high-quality polypropylene strands woven into a 90% open mesh. When used with properly installed flashing, its unique shape breaks up mortar droppings and prohibits mortar from preventing the free flow of water to weep holes.
MORTAR TRAP
H&B
H&B's Textroflash™ Flashing is a thru-wall or surface-mounted flashing with a 40-mil thick composite membrane with a proprietary high-tack adhesive. This adhesive is factory-laminated to rugged, polyethylene sheeting, yielding a flexible membrane that is suitable for application to masonry, concrete, steel, gypsum and wood.
TEXTROFLASH
.jpg)
QUART
H&B
HB SEALANT
HB SEALANT is a multi-purpose, resilient joint sealant that combines economy and high performance. It is ideal for a wide range of applications where joint movement requires compression and extension in excess of 25%.
The HB Sealant is an accessory to H&B's non-asphaltic flashing lines. It is used primarily for lapping and sealing flashings, drip edges, terminations, and end dams, particularly in areas where moisture is likely to be a factor.
METAL
The 2-SEAL™ TIE is an innovative single screw veneer tie for metal stud construction
-
Fabricated from carbon steel with a premium quality organic polymer coating, the 2-SEAL™ TIE has a dual-diameter barrel with factory-installed EPDM washers to seal both the face of the insulation and the air/vapor barrier
-
This is an improvement over single barrel types which only seal at the insulation and render the vapor barrier susceptible to air and moisture infiltration if not precisely installed (perfectly perpendicular to the stud)
-
#12 screw integrated into the dual-diameter barrel
H&B
2-SEAL
H&B
ENVIROBARRIER VP
5 GAL
The reformulated ENVIRO-BARRIER™ VP is a single component, fluid applied, vapor permeable air and water barrier for above grade wall assemblies. It cures to form a resilient, monolithic, fully adhered elastomeric membrane, which resists air leakage and water penetration but allows vapor diffusion.
THERMAL WING NUT
The Thermal Concrete 2-Seal™ Wing Nut is an innovative single screw veneer tie for concrete, CMU, or wood stud construction. The anchor features a dual-diameter barrel with factory-installed EPDM washers to seal both the face of the insulation and the air/vapor barrier, and unique Thermal Wings that are designed to decrease thermal transfer through rigid insulation.
H&B
CONCRETE STUD
THERMAL WING NUT
The Thermal 2-Seal™ Wing Nut Anchor is an innovative single screw veneer tie for metal stud construction, it features a dual-diameter barrel with factory-installed EPDM washers to seal both the face of the insulation and the air/vapor barrier, and unique Thermal Wings that are designed to decrease thermal transfer through rigid insulation.
H&B
STEEL STUD
1-1/2"
H&B
HB 200
The HB-200-X improves upon the standard HB-213 by adding three pronged punch-outs that project from the back of the anchor. The prongs prevent positive wind-loads from crushing the wallboard by transferring these loads to the back of the stud.
Ties the masonry veneer to the substrate. The The Concrete Seal Tie's screw portion has special alternating threads making it suitable for use with concrete, CMU, wood stud or brick backup, and is provided with EPDM sealing washers.
-
Consists of a Concrete Seal Tie combined with the 2-Seal™ Byna-Lok Wire Tie
-
The special point affords easy installation into a predrilled hole.
-
Barrel portion available in 5/8" - 5" lengths to accommodate thickness of insulation.
CONCRETE STUD
H&B
2-SEAL
.jpg)
H&B
2X-HOOK
The compressed leg 2X-HOOK™ has been tested and designed to withstand over 200-lbf, in tension or compression, at maximum allowed offset of 1-1/4” (disengagement of the pintle from the veneer anchor).
-
2X-HOOK™ CAN BE INSTALLED WITH LEGS POINTING UP OR DOWN.
-
The embedded portion of the 2X-HOOK is 3/16”DIA round wire, satisfying the code requirement that the mortar bed thickness (typically 3/8”) must be twice the diameter of the wire.
H&B
HB-5213
HB-5213 adjustable veneer anchor designed to anchor masonry to concrete, block or brick, accommodating rigid insulation up to 6 inches (75mm) thick.
-
Furnished with one 7/16ӯ hole for use with 523 Brass Expansion Bolt.
-
The eyelets allow 2X-HOOK™ (pintle) insertion (1 1/4" maximum allowable eccentricity) and are sized to prevent in-and-out movement beyond allowable tolerances.
-
The embedded portion of the 2X-Hook is 3/16”DIA round wire, satisfying the code requirement that the mortar bed thickness (typically 3/8”) must be twice the diameter of the wire.
H&B
HB-213
The HB-213 is an adjustable veneer anchor for metal stud and wood stud construction.
-
The L-shaped plate section has numerous ribs for added strength and 9/32" holes for connecting screws.
-
The eyelets allow 2X-HOOK™ (pintle) insertion (1 1/4" maximum allowable eccentricity) and are sized to prevent in-and-out movement beyond allowable tolerances.
-
The embedded portion of the 2X-Hook is 3/16”DIA round wire, satisfying the code requirement that the mortar bed thickness (typically 3/8”) must be twice the diameter of the wire.
H&B
The X-SEAL® Veneer Anchor is packed with more features than any other anchor on the market. Owners, architects and masons can be confident in the performance of an "X-SEALED" metal stud / veneer wall. The X-SEAL® Anchor is the next generation veneer anchor from H&B. The pronged legs bridge the sheathing and abut the steel stud, affording independent, positive anchorage. Compression of the sheathing by positive loads is also prevented
X-SEAL